Galil SAR Project Barrel, 13", 1 in 7 Twist, 5.56x45 NATO, Parkerized, US Made 922(r) Part *Oxidization in Bore* Sold *As Is*

SKU
BBL-18972
Out of stock

US manufactured Galil SAR Project Barrel, 13" length, threaded muzzle, 5.56X45 NATO/.223, parkerized, 922(r) Compliance Part, *Oxidyzation in Bore* Sold *As Is* with no returns accepted.

Sold individually.
These barrel bores were exposed to something that caused moderate oxidization from muzzle to the chamber.
The exterior of the barrels is parkerized and was not effected.

Bore will need to be neutralized immediately and heavily cleaned before use.
*NEW* US made 4150 GBQ steel with 6 grooves, 1-7 twist rate, phosphate finish.
The gas port is not drilled, handguard retainer NOT cut, threaded at the muzzle for factory flash hider (13x1mm RH).
The extractor clearance cut will need to be made once the barrel is timed to your receiver.
To fit the longer gas block with a rear mounted bayonet lug, that journal shoulder will need to be machined back.
These barrels are US made, and count as one part toward 922(r) compliance.
Due to these barrels needing cleaning/servicing, they will be sold *As Is*, and returns will NOT be accepted under any circumstance.

NOTE: Prior to installing this length of barrel into a rifle a NFA Form 1 must be completed and returned approved.
A 13 Inch length barrel installed into a shoulder fired firearm is a "Short Barreled Rifle" under the NFA. 

Installation and fit of a barrel must be inspected and tested by qualified and competent gunsmith or armorer before use in a firearm. 
Not all firearm parts are interchangeable; use of surplus parts without proper knowledge could cause a firearm to malfunction and cause property damage, injury or death.

US manufactured Galil SAR Project Barrel, 13" length, threaded muzzle, 5.56X45 NATO/.223, parkerized, 922(r) Compliance Part, *Oxidyzation in Bore* Sold *As Is* with no returns accepted.

Sold individually.

These barrels are 13 inches long, profiled for Galil SAR rifle.
These barrel bores were exposed to something that caused moderate oxidization from muzzle to the chamber.
The exterior of the barrels is parkerized and was not effected.

Bore will need to be neutralized immediately and heavily cleaned before use.
*NEW* US made 4150 GBQ steel with 6 grooves, 1-7 twist rate, phosphate finish.
The gas port is not drilled, handguard retainer NOT cut, threaded at the muzzle for factory flash hider (13x1mm RH).
The extractor clearance cut will need to be made once the barrel is timed to your receiver.
To fit the longer gas block with a rear mounted bayonet lug, that journal shoulder will need to be machined back.
These barrels are US made, and count as one part toward 922(r) compliance.

Due to these barrels needing cleaning/servicing, they will be sold *As Is*, and returns will NOT be accepted under any circumstance.

NOTE: Prior to installing this length of barrel into a rifle a NFA Form 1 must be completed and returned approved.
A 13 Inch length barrel installed into a shoulder fired firearm is a "Short Barreled Rifle" under the NFA. 

Installation and fit of a barrel must be inspected and tested by qualified and competent gunsmith or armorer before use in a firearm. 
Not all firearm parts are interchangeable; use of surplus parts without proper knowledge could cause a firearm to malfunction and cause property damage, injury or death.

More Information
SKU BBL-18972
Weight 1.250000
Length (Dimension) 13
Height (Dimension) 1
Width (Dimension) 1
Country of Manufacture United States
Type Steel
Color Gray
Finish Parkerized
Manufacturer Made in the USA
Condition As-Is
Condition AS-IS
Barrel Length 13"
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account